0
home

Miproseal-WB Clear Sealer Chemicals

home
Miproseal-WB Clear Sealer Chemicals
Miproseal-WB Clear Sealer Chemicals
Price And Quantity
  • Kilograms/Kilograms
  • 50
  • Kilograms/Kilograms
  • 75.00 - 375.00 INR
    Product Description

    Miproseal-WB Clear Sealer Chemicals are used to shield the surface of concrete from degradation, corrosion, and staining. They either block the openings in the concrete to minimize water and salt absorption, or they form an impermeable coating that stops certain materials from getting through. High-quality sealers can nowadays prevent up to 99 percent of surface moisture. There are two types of sealers including topical sealers and penetration sealers. Overall, these sealers have the required safety and aesthetic appeal for many residential and commercial projects.

    DESCRIPTION

    MIPROSEAL-WB is a water-based pure acrylic sealer for concrete with excellent blush resistance and total resistance to yellowing from UV exposure. This sealer imparts an attractive, low gloss and protection to all concrete surfaces, and is especially suited for decorative concrete. Formulated with a very low VOC content, MIPROSEAL-WB dries to a clear, matte finish, but a higher gloss can be achieved with additional coats.

    APPLICATIONS Concrete floor for parking area, drive ways, sidewalks, stamped & stencilled concrete floor, colour & acid stained concrete floor, concrete pavers and precast slabs, natural stone etc.

    PACKAGING

    MIPROSEAL-WB is packaged in 200 Kgs. drum, 25 Kgs drum & 5 Kgs drum.

    SHELF LIFE

    1 year in original, unopened container

    CURING

    DIRECTIONS FOR USE Surface Preparation: The surface to be sealed with MIPROSEAL-WB must be structurally sound, clean, and dry. MIPROSEAL WB can be applied over a previous coat of acrylic concrete Sealer; however, when the chemical makeup of the previous sealer is unknown, a small test section is recommended to ensure compatibility. Premixing of MIPROSEAL-WB is not required. Do not thin or dilute with water or any other solvent. Application: Apply MIPROSEAL WB in a uniform, continuous film by hand held low pressure pump-up sprayer, short nap roller, or foam roller. When spraying, back roll over any sprayer overlap marks to ensure even coverage. Redistribute or remove puddles or excess MIPROSEAL WB before it dries. Follow recommended coverage rates carefully to avoid uneven or heavy applications. For best results, two thin coats of MIPROSEAL WB are recommended, with a minimum 1-2 hour interval between applications, following the prescribed coverage rates.  

    COVERAGE

    The coverage rate range is 7.4 to 9.8 m2/L and is highly dependent on substrate texture and porosity.

    NOTE: DO NOT APPLY THICKER THAN RECOMMENDED AS THIS MAY CAUSE DISCOLORATION AND POOR PERFORMANCE.

    PRECAUTIONS Do not store, transport or storage this product at very low freezing temperature. Material becomes unusable if allowed to freeze. Store between 10 dig. C to 38 C. For best application results product temperature should be between 10C to 38C with ambient and surface temperatures between 70 C to 35 C.

    CLEANING Clean tools and equipment with water immediately following use. Clean drips and overspray with warm soapy water while still wet. If not cleaned immediately, the sealer may leave an unwanted residue on painted surfaces,  

    This information, given above in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use is beyond our control. 

    Physical Properties

    Viscosity, cP

    5

    Colour

    Milky White (wet) Crystal Clear (dry)

    Dry to Touch

    less than 1 hour

    Foot Traffic

    4 to 6 hours

    Wheel Traffic

    6 to 10 hours

    % Solids (by weight)

    > 25%

    Resistance to Gasoline, Brake Fluid, Solvents

    Poor

    Resistance to Acids/ Alkalis

    Medium

    Blush Resistance

    Excellent

    Trade Information
    • 100-1000000 Per Day
    • 1-7 Days
      Related Products
      Mipro-E Acid-Alkali Resistant Epoxy Resin Base Mortar


      Send Inquiry
      Mipro-K(Spl) Acid Resistant Pot. Silicate Mortar


      Send Inquiry
      Mipro-Cem Sbr Chemicals


      Send Inquiry
      Miproglass 101-Sv Glass Flake Reinforced Coating


      Send Inquiry
      Mipro-EP Primer Epoxy Coating


      Send Inquiry
      Miproglass 101-E Glass Flake Reinforced Coating


      Send Inquiry
      right arrow
      left arrow
      Contact Us

      Plot No. 2114, Phase-III, G.I.D.C., Vatva, Ahmedabad, Gujarat, 382445, India
      Phone :+918037261488