Mipro-K(Spl) Acid Resistant Pot. Silicate Mortar

Mipro-K(Spl) Acid Resistant Pot. Silicate Mortar
Mipro-K(Spl) Acid Resistant Pot. Silicate Mortar
Price And Quantity
  • Kilograms/Kilograms
  • 100
  • Kilograms/Kilograms
  • 15.00 INR
    Product Description

    INTRODUCTION: MIPRO-K(SPL) is Inorganic Special grade Pot. Silicate type, two-part chemical setting mortar. It is recommended against permanently acidic condition, and can withstand much higher temperature compared to other resin type & sulfur type mortar. Most recommended against conc. Sulfuric, Nitric and Chromic acid conditions.

    AREA OF APPLICATION MIPRO-K(SPL) is principally used with acid resisting bricks and tiles for acid resisting masonry construction, because of its very low cost. It is highly recommended to protect chimneys, incinerators and other high temperature equipment. Excellent resistant to 98% Sulfuric acid, conc. nitric acid. Highly recommended for use in sulfuric acid, Nitric acid & Chromic acid conditions. Electroplating plant lining.  

    Physical Properties



    Mix Ratio by wt. Sol to Powder


    Compressive Strength kg/cm2


    Flexural Strength kg/cm2


    Bond Strength kg/cm2




    Max. Temp.

    900 C

    Setting Time

    8-10 hrs.




    MIXING:MIPRO-K(SPL) is prepared by mixing solution & powder to form workable mortar. The recommended ratio of mixing is 1 part solution to 3 parts powder by wt. This ratio will vary depending upon ambient temperature and working conditions. Use clean dry mixing pan. Place appropriate quantity of solution in mixing Pan, and add powder slowly and start mixing thoroughly, until you get smooth paste like mortar. Do not mix more material, then, can be used within 30 minutes. 

    APPLICATION: Mortar is buttered on acid resistance brick/tile as usual bricklayers Method. Brick/tile also should be clean, dry and at ambient temperature. After hardening of the joints, it should be treated with 10 % Hydrochloric acid before the acid resisting lining is place in use. During & after completion of lining, area must be kept dry and free from any other materials and traffic, which can affect setting & curing of MIPRO-K(SPL).  

    CHEMICAL RESISTANCE MIPRO-K(SPL) when completely set hard, resistant to high concentration of oxidizing acids like 98% sulfuric acid, conc. nitric acid chromic acid etc.., inorganic acids and salts and most organic solvents at high temperature. It is not recommended against Hydrofluoric acid, fluorides, fluoride salts, water, diluted solutions, alkalis etc 

    STORAGE & SHELF LIFE always keep solution and powder in cool, dry place and away from direct sunlight, moisture etc. If stored in sealed container as above, shelf life of solution: 12 Months Powder: 12 Months  

    PACKING SOLUTION: 25 kgs & 250 kgs (net) good quality MS drums. Powder: 50 kgs (net) LDPE+HDPE bags.

    HEALTH & SAFETY It is advisable to wear protective wears at the time of use of MIPROK(SPL) and all other MIPRO brand products. In case of contact with skin or eyes wash with plenty of water and consult a doctor.  

    This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without any guarantee since the conditions of use are beyond our control. 

    Trade Information
    • 100-1000000 Per Day
    • 1-7 Days
      Related Products
      Mipro-Fa Acid-Alkali Resistant Furan Resin Base Mortar

      Send Inquiry
      Mipro-EP Primer Epoxy Coating

      Send Inquiry
      Mipro-Cem Sbr Chemicals

      Send Inquiry
      Mipro-E Acid-Alkali Resistant Epoxy Resin Base Mortar

      Send Inquiry
      Mipro-Eta Epoxy Coating

      Send Inquiry
      Mipro-E(Hyb) Acid-Alkali Resistant Hybrid Epoxy Resin Base Mortar

      Send Inquiry
      right arrow
      left arrow
      Contact Us

      Plot No. 2114, Phase-III, G.I.D.C., Vatva, Ahmedabad, Gujarat, 382445, India
      Phone :+918037261488