Mipro-Epr Epoxy Repair Mortar

Mipro-Epr Epoxy Repair Mortar
Mipro-Epr Epoxy Repair Mortar
Price And Quantity
  • Kilograms/Kilograms
  • 100
  • Kilograms/Kilograms
  • 385.00 - 650.00 INR
    Product Description

    Epoxy Repair Mortar is a two-component epoxy resin mortar with a high strength that can be troweled on to concrete and masonry surfaces for fast and lasting repairs. It is a pre-packaged, ready-to-use unit. This kind of mortar is impact and abrasion resistant, as well as has a fast curing time. Epoxy mortars and concrete are made up of a mixture of epoxy and cement, or epoxy and sand with coarse aggregate. Furthermore, the Epoxy Repair Mortar shrinks very little or not at all.


    MIPRO-EPR is a 3 component high strength, solvent-free epoxy resin repair mortar with High quality graded quartz filler and special mineral filled for high strength and excellent abrasion resistance. MIPRO-EPR is a three part mortar, supplied in kit size for ready to use at on-site for easy mixing and use.


    MIPRO-EPR is used for the repairing of concrete and plastered surface for fast and permanent repair. This will give high strength, high abrasion resistance and excellent chemical resistance. This mortar is manufactured for horizontal surface application, but can be applied vertically also when add special thixotropic paste in the system to avoid sagging.  

    It is ideally suited for all kind of damage and corroded concrete surface including acid tanks, sea walls, commercial & industrial floors. MIPRO-EPR can be used for emergency repairs where fast strength gain is important.  



    • Very High Physical Strength
    • Fast Development Strength  Minimum Down Time
    • Excellent Abrasion resistance thus suitable for high traffic areas
    • Excellent acid/alkali/Chemical Resistance
    • Excellent Bond Strength to damp Concrete Surface
    • impermeable to water  


    Clean the concrete surface with suitable means to remove any dust, loose material, plaster, previously applied coating/paint, grease and algae. Grind the surface to remove laitance. Repair mortar to a depth of at least 5mm to avoid featheredging and to provide a square edge.


    The substrate should be primed using MIPRO-PR Epoxy primer. The primer should be mixed in the proportions supplied, adding the entire contents of Part B to the Part - A. The two components should be thoroughly mixed together, for 3 minutes. The mixed primer should be applied well into the prepared concrete surface. If the primer is absorbed within 30 minutes, a second coat should be applied before continuing. MIPRO EPR can be applied as soon as the primer has started to gel but still has surface 'tack'. This is normally between 30 minutes and 4 hours dependent on the ambient and substrate temperatures. If the primer cures hard, a second application must be made before application of MIPRO-EPR. 


    Mix MIPRO-EPR is thoroughly to produce a fully homogenous, trowellable mortar. Part  A & Part  B should be mixed thoroughly. Add the filler slowly with the stirrer running and continue for 2 to 3 minutes until all the three parts are thoroughly mixed.  


    Apply the mixed MIPRO-EPR mortar to the prepared concrete surface by steel trowel, pressing firmly into place to ensure good adhesion and full compaction. Thoroughly compact the mortar. Finish mortar with trowel. MIPRO-EPR mortar can be applied in sections up to 50mm thickness in horizontal locations or up to 12mm thickness in vertical locations in a single application and without the use of formwork.  

    Note: The coverage figures given above are theoretical due to wastage factors and the variety and nature of possible substrates, practical coverage figures will be reduced.

    SHELF LIFE & STORAGE All products have a shelf life of 12 months at 30 C if kept in a dry store in the original, unopened bags or packs. Storage conditions Store in dry conditions in the original. Unopened bags or packs. If stored at high temperatures, the shelf life may be reduced to 4 to 6 months. 


    Physical Properties

    Test method

    Typical result

    Compressive strength Kg/cm2 7 days

    600 Kgs/cm2

    Flexural strength Kg/cm 2 7 days

    205 Kgs/cm2

    Tensile strength Kg/cm2 7 days

    110 Kgs/cm2

    Pot life

    30 minutes 25 C

    Initial hardness

    24 hours

    Full cure

    7 days

    Fresh wet density

    Approx. 2000kg Per M 3

    Trade Information
    • 100-1000000 Per Day
    • 1-7 Days
      Related Products
      Mipro-EC Epoxy Coating

      Send Inquiry
      Miproglass 101-I Flake Glass Reinforced Coating

      Send Inquiry
      Mipro-Wbe Epoxy Coating

      Send Inquiry
      Miproseal-WB Clear Sealer Chemicals

      Send Inquiry
      Mipro-Cp Acid-Alkali Resistant Cashew Phenolic Resin Base Mortar

      Send Inquiry
      Miproglass 201-I Glass Flake Reinforced Lining

      Send Inquiry
      right arrow
      left arrow
      Contact Us

      Plot No. 2114, Phase-III, G.I.D.C., Vatva, Ahmedabad, Gujarat, 382445, India
      Phone :+918037261488